Musicserver loxone9/28/2023 Stay the LEDs still dark, please contact the Support.īoth LEDs are lit continuously, even when no cable is connected: please contact Support No Blinking / Lighting of LEDs: Verify that the network cable is plugged in correctly. The Green LED lights permanently and the orange LED flashes (by flashing is network traffic signals) all right, continue to step 2. Verify the status LEDs on the network (LAN) port of the Miniserver flashing light. Remedy:įormat SD card with Loxone Config MINI SERVER FLASHING GREEN, BUT CAN NOT BE REACHED OVER THE NETWORK Mini server reboot (power supply for about 10 seconds to disable), if behaviour remains the same:įaulty PLC program in the mini server. Miniserver no SD card recognized / not access the card. SD card with Loxone Config loud instructions format Mini server reboot (power supply for about 10 seconds to disable), if behavior remains the same: Flashing the status LED is green, the following shall mean: The boot process takes about 7 seconds, after the green status LED Miniserver flashes at regular intervals. After activating the power supply starts the Mini Server. Activate the power supply only when the wiring work has been completed on the mini server. Take your Miniserver from the package and connect the power supply and the network. If you have followed all the steps in the getting started section about connecting directly and still cannot connect please contact support. Please make sure that you have assigned a static IP address to your laptop. The Miniserver is directly connected to your laptop or computer. Please contact support if you are still having problems.Ĩ. If not please recheck steps 3 and 4.ħ.2 If the ping failed then it is likely the network settings haven’t been setup correctly as long as you have checked steps 3 and 4. The ping should be successful and you should be able to connect to the Miniserver. Follow these steps to setup and ping the Miniserver.ħ.1 Setup is successful and the Miniserver is on the same subnet as your router. Important: The network must be classified as a home or workplace network on your Windows PC! You can now connect to the Miniserver, if not please go to step 6.Ħ. If you are using Parallels software on a Macbook make sure that your network is bridged not shared! You can now connect to the Miniserver, if not please go to step 5.ĥ. Some antivirus software will still block outgoing traffic with Loxone Config even if you have done this so it is best to temporarily disable antivirus programs when using Loxone Config. Check whether you have not made an exception for Loxone Config in your firewall or antivirus software. You can now connect to the Miniserver, if not please go to step 4.Ĥ. Check again that the network cable is connected correctly. If no Miniserver is listed in the search results continue to step 3.ģ. The Miniserver should show up in the search results and you can connect to it by double clicking on it. Open Loxone Config and search for the Miniserver. The Miniserver status LEDs should be flashing green and the network socket LEDs should be green on and amber flashing. If the LEDs stay the same pleasecontact support.ġ.3 If both LEDs are on constantly, with or without a cable connected please contact support.Ģ. If this is all correct continue to step 2.ġ.2 If both or one LED is not flashing/not lit up then check first that the network cable is connected correctly and the cable has been tested or replaced. Verify that the status LEDs on the network (LAN) port of the flash or are lit up.ġ.1 The green LED should be lit constantly, the amber LED should flash. If the Miniserver is flashing green but you cannot connect to it in Loxone Config use the following table to resolve the issue: Stepġ. There is a faulty PLC program in the Miniserver. If the behaviour remains the same then format the SD card to factory defaults according to the instructions. Check that the SD card is inserted correctly.Ģ. Reboot the Miniserver and extensions (by turning the power supply off for about 10 seconds until rebooting). The green connector power plug should NOT be removed if the power supply is on.ģ. The Miniserver does not recognise the SD card or cannot access the card.ġ. If this is not the case refer to the following table for the solution: LED statusġ. Reboot the Miniserver and extensions (by turning the power supply off for about 10 seconds until rebooting). The green connector power plug should NOT be removed if the power supply is on.Ģ. After this process the status LED on the front of the Miniserver will be flashing green. The boot process takes about 7-10 seconds. Only power up the Miniserver once all wiring has been completed. Unpack your Miniserver from its box and connect the power supply as well as a network cable from the router to the Miniserver.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |